HOW TO CONNECT SKULLCANDY EARBUDS TO IPAD

In this blog post, we’ll show you how to connect your Skullcandy earbuds to your iPad. We’ll also provide a few troubleshooting tips in case you run into any problems. Let’s get started!

There are two ways to connect Skullcandy earbuds to your iPad. The first is via Bluetooth, and the second is by using the 3.5mm audio jack. We’ll cover both methods below.

Method 1: Connecting via Bluetooth 

  1. Make sure that your Skullcandy earbuds are in pairing mode. To do this, press and hold the power button for 2-3 seconds until you see the LED light flash red and white. 
  2. Open the Settings app on your iPad and tap “Bluetooth.” 
  3. Look for “Skullcandy” in the list of available devices and tap it to pair. 
  4. Once connected, you should see a solid white LED light on your earbuds indicating that they’re ready to use. 
  5. If you ever need to disconnect, simply press and hold the power button on your earbuds for 2-3 seconds until the LED light begins flashing red and white again. Then, go back into your iPad’s Bluetooth settings and “forget” the device. 

Method 2: Connecting via 3.5mm Audio Jack 

  1. Start by inserting the small end of the included 3.5mm audio cable into the port on the bottom of your left earbud. 
  2. Plug the other end of the cable into your iPad’s headphone jack. 
  3. Once connected, you should see a solid white LED light on your earbuds indicating that they’re ready to use. 
  4. To disconnect, simply unplug the cable from your earbuds or iPad. 

Troubleshooting Tips 

If you’re having trouble connecting your Skullcandy earbuds to your iPad, try these troubleshooting tips: 

– Make sure that your earbuds are charged before attempting to connect them (a low battery can cause connection issues). You can check the battery level by pressing and holding the power button for 2-3 seconds until the LED light flashes white; four flashes means it’s fully charged, three flashes means it’s 75% charged, two flashes means it’s 50% charged, and one flash means it’s 25% charged. If necessary, charge your earbuds using the included micro USB cable and plugging them into a power source (like a computer or phone charger). – If you’re still having trouble connecting via Bluetooth, try restarting both your Skullcandy earbuds and your iPad; this can sometimes resolve connectivity issues caused by temporary software glitches. To restart your earbuds, press and hold the power button for 10 seconds until you see the LED light flash red 3 times; then release the button and wait for them to turn back on (this may take up to 30 seconds). To restart your iPad, press and hold down the Sleep/Wake button at the top of the device until you see “Slide to Power Off” appear on screen; then slide to confirm and wait 30 seconds before pressing down on Sleep/Wake again to turn it back on..   – If you’re still having no luck, try resetting your Skullcandy earbuds by pressing and holding down both the Volume Up (+) and Volume Down (-) buttons at the same time for 10 seconds until you see all three LEDs flash red 3 times; then release both buttons and wait for them to turn back on (this may take up to 30 seconds). After resetting, try connecting again from scratch following either method above..   – Lastly, if all else fails, reach out to Skullcandy customer support for additional help..   We hope this blog post was helpful in showing you how to connect your Skullcandy earbuds to your iPad! For more tips on using headphones with Apple devices, check out our other blog posts or contact us today..   Thanks for reading! Connecting Skullcandy Earphones with an iPhone 6s Plus How Do I Pair My Beats Solo 3 Wireless Headphones? How Do I Pair My Beats Solo 2 Wireless Headphones? How Do I Pair My Beats Solo Wireless Headphones? How Can I Connect my Bose QuietComfort 35 II Headphones?

Conclusion:

Thanks for reading! We hope this blog post was helpful in showing you how to connect your Skullcandy earbuds to your iPad! For more tips on using headphones with Apple devices, check out our other blog posts or contact us today..

 

Leave a Comment